⎝⎛斗牛平台⎞⎠

Hello, welcome to the website of Nanning Shuanghu High Temperature Bearing Co., Ltd.!

  • Company Name: Nanning Shuanghu High Temperature Bearing Co., Ltd.
  • Company address: No. 1406, 14th floor, building 1, Nanji Anji Wanda Plaza, 55 Gaoxin Avenue, Nanning
  • Postal code: 530005
  • 24-hour hotline: 186-5316-4392
  • Company phone: 0771-5555242
  • Fax: 4008892163-217438
  • Email: worldtalk@vip.163.com
招商咨询 业务咨询
product search
GU3000 Series 800 Degree Low Speed Heavy Duty Double Row Angular Contact Ball Bearing
product details

One. Product and Technology Introduction

This series of products is a double-row angular contact ball bearing with a temperature resistance of 800 degrees and a low speed and heavy load. The minimum inner warp is 10 mm, the maximum outer diameter is 3.6 meters, the highest accuracy is P5, and the maximum use speed is 200 rpm, or the outer ring linear speed is not more than 100 meters / minute. It consists of an inner ring, an outer ring, and rolling elements. It does not require a cage. It uses a full ball structure. The number of balls is 50% more than that of ordinary bearings. The load capacity is 1.2 times higher. Both open and closed types are possible.

The key technology of double-row angular contact ball bearings is that the two channels are exactly the same, and the contact angle is accurate, otherwise it will cause uneven force early failure. We use three-dimensional simulation precision machining technology and temperature compensation technology to completely solve the technical problems of this type of high temperature bearings, and greatly extend the bearing life. Another common form of bearing failure is excessive wear of the steel ball. The main cause of excessive wear of the ball is that the radius of curvature of the ball is smaller than the radius of curvature of the channel, which makes the contact radius of the contact area of the ball smaller, resulting in stress concentration, which causes Early failure. This design uses a near-curvature design, which makes the curvature radius of the steel ball and the channel very close, the mutual contact area increases, and the bearing capacity increases in a near-square relationship. This is why the high-temperature bearings with a near-curvature design have a longer service life However, this bearing design also has limitations in use, that is, the use of speed can not be too high, otherwise it will cause the channel to jam the steel ball, affecting the rotation flexibility, general high temperature bearings use 200 rpm, the maximum can not exceed 300 rpm .

High temperature and low speed bearings can run normally without adding high temperature grease, but adding high temperature grease will increase the service life.

two. Features

1. Full ball structure and near-curvature design, large bearing capacity, 1.2 times that of ordinary bearings.

2. Lubricated with high temperature grease, no sticky matter.

3. High temperature grease has strong resistance to high temperature evaporation and long life.

4. Able to bear large radial force and axial force.

5. High temperature resistance, anti-glue, prevent the early failure of the bearing.

6. This series of bearings are suitable for high-temperature, low-speed, heavy-duty, dusty environments and difficult to maintain grease.

three. Technical Parameters

1. Model: GU3000ZZ

2. Dimensions and tolerances: Dimensions and tolerances are the same as national standards and are interchangeable

3. Durable temperature resistance: 800 degrees

4. Peak temperature resistance: 900 degrees

5. Maximum speed: 200 rpm, or the linear speed of the outer ring is less than 100 m / min

6. Dynamic load and static load: 1.2 times that of corresponding bearings

7. Lubrication form: high temperature grease lubrication or non-lubrication

8. Structural seal: open / closed full-ball double-row maintenance-free

four. Precautions

1. The installation part is selected to be isolated from high heat and does not directly radiate the mechanical part.

2. Each bearing on the production line is evenly stressed.

3. High-temperature bearings are selected according to relevant national technical standards, or shaft f6 and seat M7 are recommended.

4. If you have any questions during use, please contact us.


Links: Nanning Boxin high temperature bearing Shuanghu high temperature bearing high temperature bearing Tesco
天天电玩城 七乐彩 欢乐拼三张 欢乐拼三张